DIY Project
DIY Project
our components
YOUR IDEA
Active and Passive Components
Active and Passive Components
Sensors and Development Board
Available at Best Prices
shop now
Free shipping

On all orders over ₹999.00

Free Replacement

Returns are free within 7 days

Support 24/7

Contact us 24 hours a day

100% Payment Secure

Your payment are Safe

Deals Of the Day

115.00
  • Perfectly fit on the extruder
  • Noiseless Performance
  • Very low Current consumption
  • Easy to install and connect.
38.00
  • Reduces the risk of hardware failure due to overheating
  • A low profile, will fit into most cases.
  • Simple, Passive cooling. No need for noisy fans.
  • Perfectly sized for the RPis CPU
48.00
  • Reduces the risk of hardware failure due to overheating
  • Low profile, will fit into most cases.
  • Simple, Passive cooling. No need for noisy fans.
  • Perfectly sized for the RPis CPU
300.00
  • Resolution: 5 MP
  • Interface Type: CSI(Camera Serial Interface)
  • Dimensions: 25x23x8 (LxWxH) mm
  • Supported Video Formats: 1080p @ 30fps, 720p @ 60fps and 640x480p 60/90 video
  • Fully Compatible with Raspberry Pi 3 and 4 Model B
  • Plug-n-Play camera for Raspberry Pi 3 and 4 Model B.
199.00
  • Easy two-piece installation design
  • Hole for mounting the pi inside the case
  • Rubber pad grip at the bottom
  • Precise access to all port and status LEDs with Symbols
  • Raspberry LOGO on Top
299.00
  • RP2040 microcontroller chip designed by Raspberry Pi
  • Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz
  • 264KB of SRAM, and 2MB of on-board Flash memory
  • Castellated module allows soldering direct to carrier boards
  • USB 1.1 with device and host support
  • Low-power sleep and dormant modes
  • Drag-and-drop programming using mass storage over USB
  • 26 × multi-function GPIO pins
  • 2 × SPI, 2 × I2C, 2 × UART, 3 × 12-bit ADC, 16 × controllable PWM channels
  • Accurate clock and timer on-chip
  • Temperature sensor
  • Accelerated floating-point libraries on-chip
  • 8 × Programmable I/O (PIO) state machines for custom peripheral support
199.00
  • Operating Voltage: 5V DC
  • Current Consumption: <60mA
  • Testing Voltage: 0-100V
  • Testing Current: 1-100A
  • Easy to read even in dim light
125.00
  • 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
  • 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes.
  • Can run motors on 4.5VDC to 25VDC.
  • Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
  • Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, or interleaved stepping.
300.00
  • Stackable design, easy to plug into the ARDUINO development board.
  • Coupled with the Arduino Bluetooth Bee Bluetooth module, and other Bluetooth devices can communicate Wirelessly.
  • 3.3v and 5v dual power output.
  • 3.3v and 5v IO compatible.
  • USB2.0 protocol.
120.00
  • Runs on 12-36VDC
  • GRBL 0.9 compatible
  • 4-Axis support
  • Compact design
  • 2 x End stops for each axis (6 in total)
80.00
  • It has a nice standard 0.1″x0.1″ prototyping grid with big pads
  • Comes with Stacking headers and plain header, choose whichever you want when soldering together
  • An IC pattern for adding DIP ICs up to 20 pins
  • Power rails down the middle and sides
  • A reset button and an extra general use button
  • Two 3mm general use LEDs, red and green, as well as 2 matching resistors
1,200.00
  • Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet.
  • Stackable Design, can directly be supported by for Arduino official Ethernet Library.
  • Supports up to four simultaneous socket connections
  • Can be used to store files for serving over the network.
  • Compatible with the for Arduino Duemilanove (168 or 328), Uno as well as Mega (1280/2560).
  • Can be accessed using the Mini SD TF library.
  • The current shield has a Power over Ethernet (PoE) module designed to extract power from a conventional twisted pair Category 5 Ethernet cable.
  • IEEE802.3af compliant
  • Low output ripple and noise (100mVpp)
  • Overload and short-circuit protection
  • 1500V isolation (input to output)

Sensors & Modules

Development Boards